King Computer Solutions
spacer

Posts Tagged Asterisk

06.27.2011

How to configure Busy Lamp Field BLF on Linksys SPA942 with asterisk to show other line status

If you are using a Linksys SPA942 and would like to enable viewing of other users status, or be able to press a button to call that extension here is how to configure Make sure you have the latest phone firmware 6.1.5(a). Connect to the web interface on the SPA942 and under the info tab […]

04.30.2011

Outbound dial pattern in asterisk for USA numbers from Australia using Anveo

I setup a US number with anveo $2.49 setup and $1.49 per month for a DID. Online chat support was helpful and they have a comprehensive call routing system including being able to accept faxes on the DID, setup voicemail etc. Call quality is good from Australia to US numbers. Incoming calls worked fine on […]

03.2.2011

Asterisk audio inbound or outbound not working when iptables firewall enabled

Due to attempted hacks on VOIP boxes we need to increase security by allowing SIP access only from the relevant IPs using iptables firewall In the case below the Asterisk VOIP server is sitting behind a NAT firewall and has the relevant config set for this. I found upon enabling the linux firewall that while […]

09.1.2010

Call forward to mobile cell phone rings and can answer but has no sound on asterisk server

If running your asterisk server behind a firewall you may experience these symptoms: internal users can call mobile extensions configured with follow me and the call goes through and can be heard with no problem. If you have a rule configured so that external callers after a timeout calling internal extensions are then routed to […]

08.2.2010

Voicemail not working and drops out after elastix asterisk backup and restore

After doing a backup of asterisk from one system, and restoring to a fresh build, you may find that when someone goes to voicemail, there is a seconds silence then it drops out. If you use *97 and try to record a message, it immediately drops back to the options to save the message without […]

07.6.2010

Asterisk command line interface (CLI) commands

Below are a list of commands you can use from the Asterisk command line interface (CLI) The CLI is reached by using the Linux shell command asterisk-

07.4.2010

Configure linksys spa400 with asterisk elastix voip server

The SPA400 operates as a single SIP trunk, it does not allow you to configure per port settings. Its therefore OK to use in a rotary incoming line situation, but not good if you want to redirect particular ports to particular SIP extensions. In that case you may use a Patton or Digium card. Connect […]

06.5.2010

Script to backup Asterisk folders

The key folders to backup for asterisk are /etc/asterisk /var/log/asterisk /var/lib/asterisk /var/spool/asterisk /usr/lib/asterisk /var/lib/mysql /usr/local/tomcat/webapps You can use this script to back them up into one gz file. ora=`date ‘+%Y.%m.%d-%H.%M.%S’` tar zcf etc-asterisk-$ora.tar.gz /etc/asterisk tar zcf var-log-asterisk-$ora.tar.gz /var/log/asterisk tar zcf var-lib-asterisk-$ora.tar.gz /var/lib/asterisk tar zcf var-spool-asterisk-$ora.tar.gz /var/spool/asterisk tar zcf usr-lib-asterisk-$ora.tar.gz /usr/lib/asterisk tar zcf var-lib-mysql-$ora.tar.gz /var/lib/mysql tar […]

05.30.2010

How to Backup and restore Elastix Asterisk configuration on Cent OS to another server

I recently found this method of doing the backup/restore http://www2.elastix.org/en/component/kunena/116-security/47135-how-to-backup-elastix-for-migration.html?Itemid=58 A few things to be aware of Make sure the Elastix version is the same or higher than the version that you are transferring the backup .tar file from. Otherwise if you try to transfer to an earlier version the extensions will not transfer across […]

08.18.2009

Asterisk Music on Hold MOH Sound Choppy in and out using Pennytel and engin

When we put a call on hold using out asterisk server the Music on hold would chop in and out. We found this choppiness only occurred using Pennytel and Engin, other VOIP providers the MOH was smooth. Try this: Make sure you’ve compiled zaptel and have ztdummy loaded. Login to the server. If connecting from […]